We have stumbled upon this article pertaining to Tools You Need to Install a New Bathtub below on the web and think it made sense to share it with you over here.
Setting up a bathtub isn't precisely rocket science, but it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough project. If the old bathtub is easily available, the job can move speedily; if you have to open a wall surface to get rid of the old bathtub and place the new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub and embeded in the brand-new one. Make sure you have qualified yourself for the job as well as fit trying it. As opposed to hiring a specialist to take control of a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may need an expert plumber to make tube links.
This write-up will certainly aid you install a brand-new tub in your shower room if you have already gotten a new tub and do not need to change the setup of your previous water pipelines.
Your devices as well as product checklist need to make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be quite troublesome because of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly originate from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place in between the faucet as well as the sink. Protect the tap in place with the supplier given backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Utilizing the two wood boards under its feet, place the bathtub in the called for position. The wooden boards are handy in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bath tub till the level reads degree.
To mount taps, fit the bottom of the outermost versatile faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply and also inspect all joints and also new pipework for leakages and tighten them if essential. Fill the tub as well as likewise check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling and also sealing around the tub needs to wait up until the bath tub has been utilized at least when as this will settle it into its final position.
Getting ready for the Installation
To start with, the supporting framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can split relatively early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently available on the market. It is recommended to fit the tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very eager about Tools You Need to Install a New Bathtub and I am assuming you enjoyed the new entry. Sharing is nice. You won't know, you may just be helping someone out. Many thanks for going through it.
Quality care? Call.